Digiop BLK-IPS101 Przewodnik Instalacji Pobierz pdf

www.digiop.com

BLK-IPS101_CQ

5/27/11

Attach peripheral devices to the terminal blocks as needed. For detailed interface specications, refer to the

user manual.

Step 2. Connect the camera to the LAN

Attach the network LAN cable to the Ethernet connector on the camera backpanel.

Your camera can be powered locally with a 12 V DC adapter, or across the LAN (PoE). If using the power

adapter, attach the DC jack adapter cable to the DC 12V power adapter terminals on the back of the camera.

Connect the red wire of the adapter cable to the + terminal, and the black (or white) wire to the - terminal.

DO NOT apply power to the camera at this time.

DC Jack

Adapter

Cable

Step 3. Install IPAdmin Tool

The IPAdminTool is a utility for conguring the network settings of your Digiop Black cameras and installing

new rmware. It can be loaded on a Microsoft Windows XP, Vista or Windows 7 operating system. At a

computer on the same LAN (subnet) where your cameras will be installed, do the following:

1. Insert the CD mini disk provided with your camera into your computer’s CD ROM drive and open the

CD in a Windows Explorer window.

2. Find the IPAdminTool directory on the CD.

3. Copy the IPAdminTool directory with its contents to your computer hard drive.

Step 4. Configure the network settings of you camera

When your IP camera is attached to a network and initially powered on, it attempts acquire compatible

network settings from a DHCP server. If it cannot nd a DHCP server, it congures itself with the following

static (xed) settings, which may or may not be compatible with other devices on the network.

IP address: 192.168.0.100

Subnet mask: 255.255.255.0

Gateway: 192.168.0.1

Your camera must be congured with static network settings that are compatible with the LAN. If your

LAN has a DHCP server, use the following sub-step. Otherwise, use the sub-step procedure below for LANs

without DHCP.

Installing cameras on LANs with DHCP

1. Connect your camera to the LAN, then power on the camera.

2. Open the IPAdminTool directory on your computer, then double click the le IPAdminTool.exe to

start the application. When the IPAdmin Tool starts, it will discover all the IP devices it supports that

exist on the network. The discovery process may take a few minutes.

H.264 Network IP Camera

Quick Installation Guide

This document guides you through the basic steps to install and congure your Digiop® Black BLK-IPS101 IP

camera. For detailed instructions, refer to the User Manual.

Find the camera’s MAC address on the product label and enter it here: __________________

Step 1. Install the camera

Install the camera mounting bracket using the instructions provided with the bracket.

Attach the adapter for mounting the camera to side with the label or to the opposite side with the four

screws provided.

Mounting

adapter

Remove the protective cap covering the camera CCD.

Attach the lens assembly to the camera by screwing it clockwise onto the camera until it is fully seated. The

lens may require a mounting ring adapter to t onto the camera.

Tighten the lens set screw with the hex wrench provided.

If the lens assembly has an Auto Iris feature, attach the lens cable to the 4-pin connector on the back of the

camera.

Attach the camera to the mounting bracket.

CONNECTIONS

Connections to the camera for audio in and out (microphone and speaker), D/I sensor, alarm, and RS-485

control are made through the 9-pin terminal block. Plug the terminal block into the mating connector on

the camera.

1 2 3 4

Podsumowanie treści

Strona 1 - Quick Installation Guide

1www.digiop.comBLK-IPS101_CQ 5/27/11Attach peripheral devices to the terminal blocks as needed. For detailed interface specications, refer to the use

Strona 2 - Static Option

Strona 3

Strona 4 - AIM AND FOCUS THE CAMERA

Więcej dokumentów dla Kamery ochrony Digiop BLK-IPS101

Aby wyświetlić dokument Digiop BLK-IPS101 Instrukcja Konfiguracji

Digiop BLK-IPS101 Instrukcja Konfiguracji (47 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Digiop BLK-IPS101 Przewodnik Instalacji

Przeglądaj online lub pobierz Przewodnik Instalacji dla Kamery ochrony Digiop BLK-IPS101. Digiop BLK-IPS101 Installation guide Instrukcja obsługi

Podsumowanie treści

Więcej dokumentów dla Kamery ochrony Digiop BLK-IPS101

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Kamery ochrony Digiop BLK-IPS101