Digiop BLK-IPD103 Przewodnik Instalacji Pobierz pdf

www.digiop.com

BLK-IPD103_CQ

Route the wire end of the power extension cable into the camera, connect it to the 12 VDC power

connector, but DO NOT apply power to the camera at this time.

Connect the other end of the power extension cable to the DC12V power adapter. The polarity of the

adapter connector is shown in the following diagram.

CAUTION



When applying power to the camera, ensure that the polarity is correct. An incorrect connection

may cause a malfunction and can damage the camera.

Step 3. Install IPAdmin Tool

The IPAdminTool is a utility for conguring the network settings of your Digiop Black cameras and installing

new rmware. It can be loaded on a Microsoft Windows XP, Vista or Windows 7 operating system. At a

computer on the same LAN (subnet) where your cameras will be installed, do the following:

1. Insert the CD mini disk provided with your camera into your computer’s CD ROM drive and open the

CD in a Windows Explorer window.

2. Find the IPAdminTool directory on the CD.

3. Copy the IPAdminTool directory with its contents to your computer hard drive.

Step 4. Configure the network settings of you camera

When your IP camera is attached to a network and initially powered on, it attempts acquire compatible

network settings from a DHCP server. If it cannot nd a DHCP server, it congures itself with the following

static (xed) settings, which may or may not be compatible with other devices on the network.

IP address: 192.168.0.100

Subnet mask: 255.255.255.0

Gateway: 192.168.0.1

Your camera must be congured with static network settings that are compatible with the LAN. If your

LAN has a DHCP server, use the following sub-step. Otherwise, use the sub-step procedure below for LANs

without DHCP.

Installing cameras on LANs with DHCP

1. Connect your camera to the LAN, then power on the camera.

2. Open the IPAdminTool directory on your computer, then double click the le IPAdminTool.exe to

start the application. When the IPAdmin Tool starts, it will discover all the IP devices it supports that

exist on the network. The discovery process may take a few minutes.

Review the list of IP devices found by IPAdmin Tool. You can identify your camera by the MAC

address. If the camera was not found, click the Refresh button every minute until your camera

appears in the list.

3. After nding your camera, right click the entry, then select IP Address from the drop-down list. An

IP Setup window will open.

Continue 

Indoor/Outdoor Mini-Dome

IP Camera Quick Installation

Guide

This document guides you through the basic steps to install and congure your Digiop® Black BLK-IPD103

IP camera. For detailed instructions, refer to the User Manual.

Find the camera’s MAC address on the product label and enter it here: __________________

Step 1. Install the camera

Separate the camera cover from

the camera base. Insert the cover

removal tool into the slot on the side

of the camera, then gently twist the

tool to pry o the cover.

Using the camera for a template,

mark the location of the holes for the

mounting screws.

Drill holes for the mounting

screws and drop cable (if needed).

Depending on the mounting surface

material, wall inserts (provided) may

be required.

Anchor the camera to the mounting

surface with three screws.

Mounting

screw holes

Wall inserts

Base

assembly

Mounting

screws

Drop

cable

Step 2. Connect the camera to the LAN and power it on

Route a LAN drop cable into the camera and plug it into the LAN connector. If the camera is powered

through the LAN cable (PoE), DO NOT apply power to the camera at this time.

Monitor

Speaker

Mic

LAN

Drop

Cable

Power

Adapter

1 2 3 4

Podsumowanie treści

Strona 1 - IP Camera Quick Installation

1www.digiop.comBLK-IPD103_CQ Route the wire end of the power extension cable into the camera, connect it to the 12 VDC power connector, but DO NOT app

Strona 2 - Static Option

2www.digiop.comStatic Option4. In the IP Setup window, click the Static option bullet. If you have other compatible network settings you want to appl

Strona 3

Strona 4 - Zoom Puller

Więcej dokumentów dla Kamery ochrony Digiop BLK-IPD103

Aby wyświetlić dokument Digiop BLK-IPD103 Instrukcja Użytkownika

Digiop BLK-IPD103 Instrukcja Użytkownika (40 strony)

Digiop BLK-IPD103 Instrukcja Użytkownika (30 strony)

Aby wyświetlić dokument Digiop BLK-IPD103 Instrukcja Obsługi

Digiop BLK-IPD103 Instrukcja Obsługi (25 strony)

Digiop BLK-IPD103 Instrukcja Użytkownika (16 strony)

Digiop BLK-IPD103 Instrukcja Użytkownika (21 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Digiop BLK-IPD103 Przewodnik Instalacji

Przeglądaj online lub pobierz Przewodnik Instalacji dla Kamery ochrony Digiop BLK-IPD103. Digiop BLK-IPD103 Installation guide Instrukcja obsługi

Podsumowanie treści

Więcej dokumentów dla Kamery ochrony Digiop BLK-IPD103

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Kamery ochrony Digiop BLK-IPD103